Herringbone stitch for beginners

Updated November 5, 2026

Herringbone stitch adds beads two at a time, and each pair leans away from the other like the two sides of a V. Column by column, those Vs build the zigzag texture it is named after, the same pattern as a herringbone fabric. It is also called Ndebele stitch, after the South African beadwork tradition it is often linked to.

The result is a flexible, slightly ridged fabric with a lovely drape. It works flat for bands and cuffs, and as a tube for ropes and necklaces.

What you need

  • Round seed beads, size 11/0 or 8/0. Herringbone relies on beads that can tilt toward each other, which round beads do best. Cylinder beads such as Delicas work too, with a flatter, more angular look. Our Delica vs seed beads guide explains the difference.
  • Beading thread, such as a braided thread or a nylon beading thread.
  • A beading needle, size 10 to 12.
  • Small scissors, and a mat that stops beads from rolling away.

Use two colors when you learn, alternating them column by column. The Vs are much easier to see.

How the stitch works

Each stitch picks up two beads, then passes down through one bead of the row below and up through the next. The two new beads sit side by side on top of that pair of columns. Because the thread pulls them toward the gap between the columns, each bead tilts outward, and that tilt makes the V.

So herringbone always works in pairs of columns, and a flat piece needs an even number of beads in each row.

Start with a ladder

Herringbone usually starts from a bead ladder, the same foundation row used in brick stitch.

  1. Cut the thread. Cut about 1.5 m (5 ft) of thread, and leave a 20 cm (8 in) tail.
  2. Make a ladder of an even number of beads. Pick up two beads, pass through both again so they sit side by side, then add one bead at a time, passing through the previous bead and the new one. Four or six beads is a good size to learn with.
  3. Straighten it. Weave back through the ladder once, so that the beads sit neatly in a row. Finish with the thread coming out of the top of an end bead.

Stitch the rows

  1. Add the first pair. Pick up two beads. Pass down through the next bead of the ladder, then up through the bead after it.
  2. Add the next pair. Pick up two beads again, and pass down through the next ladder bead. Continue until every pair of columns has two new beads on top.
  3. Turn at the edge. Your thread is now coming out of the bottom of the row, at the edge. Bring it back up through the last bead you added, ready to work the next row in the other direction. You can do this by catching the thread between the edge beads of the row below and passing back up, or by adding a small extra bead at the edge as a turning bead. Choose one method and use it on every row, so that both edges match.
  4. Repeat. Each new row works the same way: pick up two beads, pass down through the next bead of the row below and up through the following one.

Pull snug after each pair. Within a few rows, the Vs will start to show clearly.

Tubular herringbone

To make a rope, join the ladder into a ring so that its first and last beads sit side by side, and work around instead of back and forth.

At the end of each round there is no turn. Instead, you step up: pass up through two beads, first the bead below the first pair of the round, then the first bead of that pair, so that the thread comes out at the top, ready for the next round. A ring of four or six beads makes a narrow rope. A wider ring makes a softer, rounder tube.

Adding thread and finishing

When about 15 cm (6 in) of thread remains, weave it back through the beadwork. Follow the existing thread path up and down the columns, changing direction a few times, and trim it close. Start a new thread a few rows back the same way, so that it comes out where you stopped.

A flat band can take a slide or fold-over clasp, or a jump ring stitched through the end rows. A rope is usually finished with end caps, which hide the last round.

Common beginner problems

  • The Vs do not show. The tension is too loose. Pull snug after every pair, so that the beads tilt.
  • The edges look different on each side. The turns are inconsistent. Use the same turning method on every row.
  • The piece twists. This is common in tubes, and many beaders like the spiral it makes. For a straight rope, check that every stitch goes into the right column.
  • A column runs out of beads. A pair was missed. Count the beads on top after each row, two per pair of columns.

Where to go next

Once flat herringbone feels steady, try a narrow tube for a simple rope necklace. For crisp, chart-based pictures, peyote stitch and square stitch are better suited, since their beads sit in a straight grid.