Square stitch for beginners

Updated November 18, 2026

A loom design from the ShineBead app. Square stitch gives exactly the same straight grid, so loom charts work for it bead for bead.
A loom design from the ShineBead app. Square stitch gives exactly the same straight grid, so loom charts work for it bead for bead.

Square stitch makes the same straight grid of beads as a loom, with no loom at all. Each bead is stitched directly to the bead below it, so the rows line up in neat columns, just like woven beadwork. It is slower than weaving on a loom, but there are no warp threads to set up or finish, and the fabric comes out firm and strong.

That makes it a good choice for small pieces such as charms, rings, bookmarks and short bands, and for anyone who wants to try loom patterns before buying a loom.

What you need

  • Cylinder beads, such as Miyuki Delica 11/0. The thread passes through each bead several times, so their large holes help, and their straight sides keep the columns tidy. Our Delica color chart lists every color by code.
  • Beading thread, such as a braided thread or a nylon beading thread, in a color close to your beads. Our thread and needles guide helps you choose.
  • A beading needle, size 10 to 12. A thinner needle makes the extra passes easier.
  • Small scissors, and a mat that stops beads from rolling away.

How the stitch works

In square stitch, the beads in each row sit side by side with their holes running along the row, exactly as on a loom. The difference is what holds them in place. Instead of warp threads, every new bead is joined to the bead directly below it by a small circle of thread: through the bead below, then back through the new bead.

Because each bead is tied to its neighbor below, a mistake stays local. If one bead is wrong, you can usually remove just that bead without the rest of the row coming loose.

Make the first row

  1. Cut the thread. Cut about 1.5 m (5 ft) of thread. Longer lengths tangle, and you will add more thread as you go.
  2. Add a stop bead. Pick up one spare bead, slide it near the end, leaving a 20 cm (8 in) tail, and pass through it once more so that it stays in place. You will remove it later.
  3. String the first row. Pick up all the beads for row one, in chart order, and slide them down to the stop bead.

Stitch the next rows

  1. Add the first bead of row two. Pick up one bead. Pass through the last bead of row one, in the same direction your thread came out of it, then go back through the new bead. The new bead now sits on top of the old one, with their holes parallel.
  2. Continue along the row. Pick up the next bead, pass through the next bead of the row below, and go back through the new bead. Repeat to the end of the row.
  3. Reinforce the row. When the row is complete, pass the needle back through the whole row below, then through the whole new row. This straightens the beads and locks the row in place. Many beaders do this after every row; at the very least, do it every few rows.
  4. Turn and repeat. Your thread now comes out at the end of the new row, ready for the next one, worked in the opposite direction.

Pull snug after each bead. The thread circles should be firm, but not so tight that the beads tilt.

Adding thread and finishing

When about 15 cm (6 in) of thread remains, weave it back through the beadwork. Follow the existing thread path, moving up or down through a column now and then, and trim it close. Start a new thread a few rows back the same way, so that it comes out of the last bead you stitched. The steps, and the half-hitch knot for extra hold, are in how to add and end thread.

Remove the stop bead at the end, and weave in the starting tail the same way. A finished piece can take a clasp, a jump ring or ear wires stitched through its edge beads, or it can be stitched to a backing.

Shaping as you go

Square stitch does not have to be a rectangle. To make a row narrower than the one below, weave through the row below until your thread comes out of the bead where the new row should start, then begin there. Weaving through existing beads like this also lets you start a row anywhere along the piece, which is handy for small motifs and cut-out shapes.

How to read a chart for square stitch

Square stitch uses the same charts as loom beading. The grid on the chart is the grid on your piece: one square on the chart is one bead, and each row of the chart is one row of stitches. Any loom chart works bead for bead.

Since you work back and forth, read the first row in one direction, the next row in the other, and so on. Mark each row as you finish it, and check the count against the chart before you reinforce.

How to size a piece

Square stitch beads sit the same way as loom beads. With Delica 11/0 beads, that gives you roughly:

  • Width: 7 to 8 beads per centimeter.
  • Length: about 6 rows per centimeter.

Stitch a few rows and measure them, since tension changes these numbers slightly. For a bracelet, choose Loom in the bead calculator to get the beads per row, the number of rows and the total to buy. You can ignore its warp thread tip, as square stitch needs none.

Square stitch or loom?

  • Choose square stitch for small and shaped pieces, for pieces you want to be very sturdy, or when you do not have a loom.
  • Choose a loom for long bands and wide pictures. Picking up a whole row at once is much faster than stitching every bead.

Common beginner problems

  • Beads tilt or lean. The thread is pulled too tight, or the circle went through the wrong bead below. Check that each new bead sits squarely on top of one bead.
  • The piece feels floppy. Reinforce more often. Passing back through the previous row and the new one is what makes square stitch firm.
  • The needle will not go through a bead. The hole is already full of thread. Switch to a thinner needle, or skip that bead when you reinforce.
  • The pattern comes out mirrored. Rows are read in alternate directions. Mark the direction of each row on the chart before you start.

Where to go next

Start with a small piece, such as a ring or a charm a dozen beads wide, so that you can reinforce often and see the grid build up. When the stitch feels steady and you want longer pieces, try loom beading with the same charts. For a staggered fabric that builds just as firmly, peyote stitch is the natural next step.