How to add and end thread

Updated November 18, 2026

Every piece longer than a pair of small earrings uses more than one length of thread. Sooner or later the thread runs short in the middle of a row, and what you do next decides whether the piece holds for years or comes apart at that spot. The good news is that it takes two minutes and there is nothing to see afterward.

This guide shows how to end the old thread, how to start a new one, and what changes from stitch to stitch.

When to stop

Stop when about 15 cm (6 in) of thread is left. That feels wasteful, but you need that much to weave back through the beadwork with the needle still on the thread. If you stitch down to the last few centimeters, the needle no longer fits through the turns, and the end cannot be secured properly.

Finish the bead or the row you are on first, so that you know exactly where to pick up again.

How to end a thread

  1. Turn back into the beadwork. Pass the needle into a bead in the row below the one you just finished, heading away from the working edge.
  2. Follow the thread that is already there. Go through three or four beads along the path the stitch itself takes. Your thread then lies next to the old one inside the beads, and nothing shows.
  3. Change direction. Turn and go through another three or four beads, then turn once more. Each turn works like a hook. A thread that runs in one straight line can slide out again; a thread that doubles back twice cannot.
  4. Trim close. Pull the thread slightly taut and cut it right at the bead with sharp scissors. When you let go, the cut end springs back inside the bead.
Ending a thread in peyote. The thread follows the stitch through a few beads, doubles back twice, and is trimmed where it leaves the last bead (×).

Stay a bead or two away from the edges while you weave. Thread that wraps around an edge bead shows, and edge beads are the ones you may need later for a clasp or an ear wire.

The half-hitch knot

Weaving in alone holds well in firm stitches. For anything that will be pulled and bent a lot, such as a bracelet, add one or two half-hitches along the way. A half-hitch is a tiny knot tied around the thread that already runs between two beads:

  1. Bring the needle out of a bead in the middle of the piece.
  2. Slide the needle under the thread between that bead and the next one.
  3. Pull the thread through until a small loop is left.
  4. Pass the needle through that loop and pull snug. The knot settles between the two beads.
  5. Go through the next few beads, so that the knot is pulled a little way into a bead hole, and carry on weaving.

Two half-hitches with a few beads between them are plenty. More knots only fill up the bead holes.

How to start a new thread

  1. Cut a new length of about 1.5 m (5 ft) and thread the needle.
  2. Enter a few rows back. Pass into a bead three or four rows behind the place where you stopped, and leave a tail of about 10 cm (4 in) hanging out.
  3. Weave toward the place where you stopped, following the thread path and changing direction two or three times, just as you would to end a thread. Tie a half-hitch on the way if the piece needs it.
  4. Come out exactly where the old thread did. Leave the last bead you stitched in the same direction as the old thread, and carry on as if nothing had happened.
  5. Trim the tail once you have stitched a row or two and the new thread sits firmly.

A tip that saves a lot of confusion: start the new thread before you end the old one. While the old thread is still hanging from the last bead, it shows you where the new one has to come out and in which direction. Then weave in the old one.

What changes from stitch to stitch

  • Peyote: the thread path runs diagonally from bead to bead. Follow a diagonal for a few beads, turn, and follow the next one back.
  • Brick stitch: the holes run up and down, so you weave down through a bead, on into the bead below it, and back up through the neighboring column. On small earrings, hide the ends in the widest rows, where there are the most beads to pass through.
  • Loom: weave the weft thread back through a row of beads, move up or down one row at the edge, and come back through the next. Tie the half-hitch around a warp thread. The warp threads themselves are finished at the very end, once the piece is off the loom.
  • Square stitch: every bead already holds several passes of thread. Change to a thinner needle if a hole feels full, and never force it: a bead that cracks in the middle of a finished piece is much harder to fix than a detour through the next bead.

The starting tail

The 20 cm (8 in) tail you left at the very beginning is ended the same way. Remove the stop bead, thread the tail onto a needle, and weave it in with two or three changes of direction.

Common problems

  • The end keeps slipping out. It was woven in a straight line. Add another change of direction, or a half-hitch.
  • The needle will not go through. The hole is full of thread. Take a different route through the neighboring bead, or switch to a size 12 or 13 needle. Our thread and needles guide explains the sizes.
  • A stub of thread sticks out. Pull the stub gently and trim again right at the bead, or pass it through one more bead first.
  • The thread shows between beads. You crossed from one bead to another where the stitch does not go. Stay on the existing thread path.
  • You cannot find where to continue. Next time, start the new thread before ending the old one.

Where to go next

Tidy ends matter most on pieces that are worn every day. Try them on a free pattern, or work out how much thread and how many beads a bracelet takes with the bead calculator. If your thread frays or tangles long before it runs out, the thread and needles guide helps you pick a better match for your beads.