Odd-count peyote stitch
Updated November 12, 2026
Odd-count peyote is flat peyote with an odd number of beads across, such as 7, 9 or 11. The stitch itself is exactly the same as even-count. The only difference is at one edge: every other row ends with a bead that has nothing to pass through, so you need a different way to turn there.
If you have not stitched peyote before, start with our peyote stitch for beginners guide. This one assumes you know how to string the first two rows, add beads in the gaps and turn at an even-count edge.
Why bother with an odd count?
An odd number of columns has a single center column. That matters for symmetrical motifs: a diamond, heart or arrow can come to a point on one bead, and a design can have a true center line. With an even count, the middle falls between two columns, so a centered motif needs two beads at its tip, or sits half a bead off center.
So if a pattern you love is 7, 9 or 11 beads wide, it is odd-count, and it is worth learning the turn instead of adding or dropping a column.
How to tell if a pattern is odd-count
Count the beads across one end of the chart, or the beads in the first string of the word chart (rows one and two together). An odd number means odd-count peyote. You will also notice that the rows alternate in length: on a piece 7 beads wide, one row has 4 beads and the next has 3.
Step by step
Use two colors and a 7-bead swatch, so you can see what each bead is doing. The numbers below match the drawing.
- String the first seven beads, leaving a tail of about 20 cm (8 in). Skip the stop bead this time, or take it off before step 4, because you will tie a knot with the tail.
- Start row three as usual. Pick up bead 8, skip bead 7, and pass through bead 6. Pick up bead 9, skip bead 5, and pass through bead 4. Pick up bead 10, skip bead 3, and pass through bead 2.
- Add the last bead of the row. Pick up bead 11. It sits on bead 1, at the edge where your tail hangs, and there is no bead beyond it to pass through. This is the odd-count edge.
- Tie the first turn. Tie the working thread and the tail together with a square knot, snug against the beads, then pass back through bead 11. You are now heading the other way.
- Work row four. Pick up bead 12 and pass through bead 10. Pick up bead 13 and pass through bead 9. Pick up bead 14 and pass through bead 8. This row has only three beads.
- Turn at the other edge as usual. Pick up bead 15 and pass back through bead 14. This edge always turns just like even-count.
- Work row five back toward the tail edge. Pick up bead 16 and pass through bead 13, then pick up bead 17 and pass through bead 12. Pick up bead 18, the last bead, which sits on bead 11.
- Make the thread-loop turn. Look at the edge below bead 18: the thread from your earlier turn makes a small loop between the edge beads. Slide the needle under that loop, pull snug, and pass back through bead 18. You are heading the other way again, ready for the next short row.
- Repeat. From now on, every row that ends at the tail edge finishes with the thread-loop turn in step 8, and every row that ends at the other edge turns as in step 6.
The other way: the figure-eight turn
Older patterns often describe a figure-eight turn instead of the thread loop. After adding the last bead, you weave back through a few edge beads of the rows below in a small figure-eight, so the thread comes out of the new bead heading the other way. It hides the thread completely, but the path is easy to lose. If a pattern you buy explains its own turn, follow that. If not, the thread-loop turn above gives the same result with far less fuss.
Tips for neat edges
- Keep the turn snug. A loose loop lets the edge bead tip outward. Pull the thread firmly after passing under the loop, then ease off before the next bead.
- Watch the row length. If a row that should have three beads ends up with four, you have probably skipped the loop and added a bead on top of the edge. Count the beads in each row for the first few rows.
- Use a thread that blends in. The thread-loop turn shows a little more thread on that edge than an even-count turn, so match the thread to your edge color. Our thread and needles guide explains the choices.
- Use cylinder beads. Delica 11/0 beads keep the columns straight, which makes an odd-count edge look as tidy as the other one. Delica vs seed beads explains why.
Sizing an odd-count piece
Sizing works the same as even-count peyote. Delica 11/0 beads are about 1.6 mm wide and 1.3 mm long along the hole. With the thread running across the band, each column adds about 1.3 mm, so a band 9 beads wide comes out at about 1.2 cm, depending on your tension. The bead calculator works out how many beads you need for any width and length, odd or even.
Where to go next
Ready to try a centered motif? Draw one in the peyote pattern maker: set an odd width and your design gets a center column for its point. For charts to follow, see how to read a bead pattern, and browse our free bead patterns for practice pieces. For wide pieces, two-drop peyote is the faster cousin: it stitches two beads at a time.